Rights statement: This is the author’s version of a work that was accepted for publication in Materials Science and Engineering: A. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Materials Science and Engineering: A, 711, 2018 DOI: 10.1016/j.msea.2017.10.102
Accepted author manuscript, 10.6 MB, PDF document
Available under license: CC BY-NC-ND: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License
Final published version
Research output: Contribution to Journal/Magazine › Journal article › peer-review
Research output: Contribution to Journal/Magazine › Journal article › peer-review
}
TY - JOUR
T1 - Stability of retained austenite in martensitic high carbon steels
T2 - Part I: Thermal stability
AU - Cui, Wen
AU - San-Martín, David
AU - Rivera-Díaz-del-Castillo, Pedro E.J.
N1 - This is the author’s version of a work that was accepted for publication in Materials Science and Engineering: A. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Materials Science and Engineering: A, 711, 2018 DOI: 10.1016/j.msea.2017.10.102
PY - 2018/1/10
Y1 - 2018/1/10
N2 - Thermal stability of retained austenite in 1C-1.5Cr steels with two Si and Mn contents is studied. Time-resolved high resolution synchrotron X-ray radiation and dilatometry are employed. The threshold transformation temperatures, decomposition kinetics, associated transformation strain, as well as the influence of Si and Mn were investigated. The coefficients of linear thermal expansion for both the bulk materials and individual phases are also obtained. The results indicate that an increase in the Mn and Si contents show little influence on the onset of retained austenite decomposition, but result in more thermally stable austenite. The decomposition is accompanied by a simultaneous increase in ferrite content which causes an expansive strain in the order of 10 − 4 , and subsequent cementite development from 300 − 350 ° C which causes a contraction that helps to neutralise the expansive strain. During decomposition, a continuous increase in the carbon content of austenite, and a reduction in that of the tempered-martensite/ferrite phase was observed. This process continued at elevated temperatures until full decomposition was reached, which could take less than an hour at a heating rate of 0.05 ° C /s. Additionally, the observation of austenite peak splitting on samples with high Mn and Si contents suggests the existence of austenite of different stabilities in such matrix.
AB - Thermal stability of retained austenite in 1C-1.5Cr steels with two Si and Mn contents is studied. Time-resolved high resolution synchrotron X-ray radiation and dilatometry are employed. The threshold transformation temperatures, decomposition kinetics, associated transformation strain, as well as the influence of Si and Mn were investigated. The coefficients of linear thermal expansion for both the bulk materials and individual phases are also obtained. The results indicate that an increase in the Mn and Si contents show little influence on the onset of retained austenite decomposition, but result in more thermally stable austenite. The decomposition is accompanied by a simultaneous increase in ferrite content which causes an expansive strain in the order of 10 − 4 , and subsequent cementite development from 300 − 350 ° C which causes a contraction that helps to neutralise the expansive strain. During decomposition, a continuous increase in the carbon content of austenite, and a reduction in that of the tempered-martensite/ferrite phase was observed. This process continued at elevated temperatures until full decomposition was reached, which could take less than an hour at a heating rate of 0.05 ° C /s. Additionally, the observation of austenite peak splitting on samples with high Mn and Si contents suggests the existence of austenite of different stabilities in such matrix.
KW - Austenite
KW - Phase stability
KW - Synchrotron radiation
KW - Dilatometry
KW - Martensitic bearing steels
U2 - 10.1016/j.msea.2017.10.102
DO - 10.1016/j.msea.2017.10.102
M3 - Journal article
VL - 711
SP - 683
EP - 695
JO - Materials Science and Engineering: A
JF - Materials Science and Engineering: A
SN - 0921-5093
ER -