Rights statement: This is the author’s version of a work that was accepted for publication in Surface and Coatings Technology. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Surface and Coatings Technology, 405, 2021 DOI: 10.1016/j.surfcoat.2020.126726
Accepted author manuscript, 3.27 MB, PDF document
Available under license: CC BY-NC-ND
Final published version
Research output: Contribution to Journal/Magazine › Journal article › peer-review
Fabrication, microstructure and micromechanical properties of Fe-based metallic glass coating manufactured by laser. / Zhang, P.; Zhang, Q.; Yan, H.; Yu, Z.; Yang, J.; Chen, J.; Wu, D.; Shi, H.; Tian, Y.; Ma, S.; Lei, W.
In: Surface and Coatings Technology, Vol. 405, 126726, 15.01.2021.Research output: Contribution to Journal/Magazine › Journal article › peer-review
}
TY - JOUR
T1 - Fabrication, microstructure and micromechanical properties of Fe-based metallic glass coating manufactured by laser
AU - Zhang, P.
AU - Zhang, Q.
AU - Yan, H.
AU - Yu, Z.
AU - Yang, J.
AU - Chen, J.
AU - Wu, D.
AU - Shi, H.
AU - Tian, Y.
AU - Ma, S.
AU - Lei, W.
N1 - This is the author’s version of a work that was accepted for publication in Surface and Coatings Technology. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Surface and Coatings Technology, 405, 2021 DOI: 10.1016/j.surfcoat.2020.126726
PY - 2021/1/15
Y1 - 2021/1/15
N2 - Iron-based amorphous alloys have received extensive attention due to their high hardness, elastic modulus/limit and wear/corrosion resistance. In this research, an attempt has been made to develop an amorphous coating of Fe-Cr-Mo-C-B-Y metallic glass coating on the steel substrate through laser surface treatment. During the test, various process parameters are used to determine the position of the amorphous phase. After coating, the microstructure and phase distribution of the coating were analyzed by scanning electron microscope, X-ray diffraction and transmission electron microscope. Mechanical properties of the coating were analyzed by using microhardness testing, abrasion resistance and nanoindentation methods. The results show that the coating thickness varies directly with the incident laser power and interaction time. The microstructure of the coating can be divided into three layers: the first layer (columnar crystals), the second layer (the crystalline phase filled with the unit structure) and the third layer (the unit structure consists of a crystalline phase and an amorphous phase). As the heat input of laser cladding decreases, the volume fraction of the amorphous phase increases, and the average microhardness and nanohardness increase.
AB - Iron-based amorphous alloys have received extensive attention due to their high hardness, elastic modulus/limit and wear/corrosion resistance. In this research, an attempt has been made to develop an amorphous coating of Fe-Cr-Mo-C-B-Y metallic glass coating on the steel substrate through laser surface treatment. During the test, various process parameters are used to determine the position of the amorphous phase. After coating, the microstructure and phase distribution of the coating were analyzed by scanning electron microscope, X-ray diffraction and transmission electron microscope. Mechanical properties of the coating were analyzed by using microhardness testing, abrasion resistance and nanoindentation methods. The results show that the coating thickness varies directly with the incident laser power and interaction time. The microstructure of the coating can be divided into three layers: the first layer (columnar crystals), the second layer (the crystalline phase filled with the unit structure) and the third layer (the unit structure consists of a crystalline phase and an amorphous phase). As the heat input of laser cladding decreases, the volume fraction of the amorphous phase increases, and the average microhardness and nanohardness increase.
KW - Amorphous coating
KW - Composite coating
KW - Laser cladding
KW - Metallic glass
KW - Nanoindentation
KW - Amorphous alloys
KW - Crystal structure
KW - Glass
KW - Iron alloys
KW - Microhardness
KW - Microstructure
KW - Scanning electron microscopy
KW - Surface treatment
KW - Thickness measurement
KW - Transmission electron microscopy
KW - Wear resistance
KW - Fe-based metallic glass
KW - Iron based amorphous alloys
KW - Laser surface treatment
KW - Microhardness testing
KW - Micromechanical property
KW - Nano-indentation methods
KW - Phase distribution
KW - Process parameters
KW - Coatings
U2 - 10.1016/j.surfcoat.2020.126726
DO - 10.1016/j.surfcoat.2020.126726
M3 - Journal article
VL - 405
JO - Surface and Coatings Technology
JF - Surface and Coatings Technology
SN - 0257-8972
M1 - 126726
ER -