Home > Research > Publications & Outputs > Influence of pyrolysis temperature on the chara...

Electronic data

  • Xu et al._JAAP

    Rights statement: This is the author’s version of a work that was accepted for publication in Journal of Analytical and Applied Pyrolysis. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Analytical and Applied Pyrolysis, 154, 2021 DOI: 10.1016/j.jaap.2020.105010

    Accepted author manuscript, 2.1 MB, PDF document

    Available under license: CC BY-NC-ND: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License

Links

Text available via DOI:

View graph of relations

Influence of pyrolysis temperature on the characteristics and lead(II) adsorption capacity of phosphorus-engineered poplar sawdust biochar

Research output: Contribution to Journal/MagazineJournal articlepeer-review

Published
  • Y. Xu
  • T. Bai
  • Q. Li
  • H. Yang
  • Y. Yan
  • B. Sarkar
  • S.S. Lam
  • N. Bolan
Close
Article number105010
<mark>Journal publication date</mark>1/03/2021
<mark>Journal</mark>Journal of Analytical and Applied Pyrolysis
Volume154
Number of pages11
Publication StatusPublished
Early online date30/12/20
<mark>Original language</mark>English

Abstract

Phosphorus (P)–engineered biochars (BCP) were prepared via co-pyrolysis of poplar sawdust and monopotassium phosphate (KH2PO4) (10 %, w/w) at 300 ℃, 500 ℃ and 700 ℃ to evaluate their potential lead [Pb(II)] adsorption. Effects of pH, contact time, and initial Pb(II) concentration on the Pb(II) adsorption capacity of the biochars were investigated. The physico-chemical, morphological, porous structure, crystallinity and spectroscopic characteristics of pre- and post-Pb-adsorbed biochars were analyzed to unravel the Pb(II) adsorption mechanism. Results showed that KH2PO4 reacted with biomass carbon to form stable C–P and/or C–O–P groups in BCP, and increased carbon retention and aromaticity of BCP. However, the addition of KH2PO4 led to an adverse effect on porous structure, e.g. surface area of biochars produced at 300 ℃, 500 ℃ and 700 ℃ were decreased by 41.53 %, 80.32 %, and 59.74 %, respectively. Adsorption experiments displayed that BCP produced at 300 ℃ exhibited the highest Pb(II) adsorption capacity (qmax = 154.7 mg g−1), which was almost 6 times higher than the pristine biochar (qmax = 24.3 mg g−1). Potassium polymetaphosphate [(KPO3)n] particles were attached on the surface of BCP, which facilitated the precipitation of Pb(II) to form [Pb(PO3)2]n, Pb5(PO4)3OH and PbHPO4. This study thus demonstrated the effect of pyrolysis temperature on the enhancing removal capability of P-modified biochar for Pb(II) from aqueous solutions.

Bibliographic note

This is the author’s version of a work that was accepted for publication in Journal of Analytical and Applied Pyrolysis. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Analytical and Applied Pyrolysis, 154, 2021 DOI: 10.1016/j.jaap.2020.105010