Results for Selective laser melting

Publications & Outputs

1. Research progress on selective laser melting (SLM) of bulk metallic glasses (BMGs): a review

   Zhang, P., Tan, J., Tian, Y., Yan, H. & Yu, Z., 28/02/2022, In: International Journal of Advanced Manufacturing Technology. 118, 7-8, p. 2017-2057 41 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

2. Influence of the microstructure on mechanical properties of SLM additive manufacturing Fe-based bulk metallic glasses

   Jiang, Q., Zhang, P., Tan, J., Yu, Z., Tian, Y., Ma, S. & Wu, D., 15/02/2022, In: Journal of Alloys and Compounds. 894, 13 p., 162525.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

3. AlCoCrFeNi high entropy alloy fabricated via selective laser melting reinforced by Fe-based metallic glass

   Jiang, Q., Zhang, P., Yu, Z., Tian, Y. & Ma, S., 15/01/2022, In: Materials Letters. 307, 5 p., 130994.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

4. Selective laser melted AlSi10Mg alloy under melting mode transition: Microstructure evolution, nanomechanical behaviors and tensile properties

   Wu, H., Ren, Y., Ren, J., Liang, L., Li, R., Fang, Q., Cai, A., Shan, Q., Tian, Y. & Baker, I., 25/08/2021, In: Journal of Alloys and Compounds. 873, 10 p., 159823.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

5. Process parameter optimization for selective laser melting of Inconel 718 superalloy and the effects of subsequent heat treatment on the microstructural evolution and mechanical properties

   Wang, W., Wang, S., Zhang, X., Chen, F., Xu, Y. & Tian, Y., 30/04/2021, In: Journal of Manufacturing Processes. 64, p. 530-543 14 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

6. Effect of melting modes on microstructure and tribological properties of selective laser melted AlSi10Mg alloy

   Wu, H., Ren, Y., Ren, J., Cai, A., Song, M., Liu, Y., Wu, X., Li, Q., Huang, W., Wang, X. & Baker, I., 8/12/2020, In: Virtual and Physical Prototyping. 15, sup1, p. 570-582 13 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

7. Generation of graded porous structures by control of process parameters in the selective laser melting of a fixed ratio salt-metal feedstock

   Aboulkhair, N. T., Zhao, G., Hague, R. J. M., Kennedy, A. R., Ashcroft, I. A. & Clare, A. T., 1/07/2020, In: Journal of Manufacturing Processes. 55, p. 249-253 5 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

8. Powder bed fusion additive layer manufacturing of titanium alloys

   Eskandari Sabzi, H., 1/05/2019, In: Materials Science and Technology (United Kingdom). 35, 8, p. 875-890 16 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

9. Effect of processing parameters on the densification, microstructure and crystallographic texture during the laser powder bed fusion of pure tungsten

   Sidambe, A. T., Tian, Y., Prangnell, P. B. & Fox, P., 1/01/2019, In: International Journal of Refractory Metals and Hard Materials. 78, p. 254-263 10 p.

   Research output: Contribution to Journal/Magazine › Journal article › peer-review

10. Salt-metal feedstocks for the creation of stochastic cellular structures with controlled relative density by powder bed fabrication

    Zhao, G., Ashcroft, I. A., Hague, R. J. M., Kennedy, A. R. & Clare, A. T., 5/07/2018, In: Materials and Design. 149, p. 63-72 10 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review