Home > Research > Researchers > Professor Allan Rennie > Publications

Research

Professor Allan Rennie

Professor in Manufacturing Engineering & Director of Engagement

101 - 125 out of 246Page size: 25
RSS feed of this list
  1. 2015
  2. Published

    Single camera photogrammetry for reverse engineering and fabrication of ancient and modern artefacts

    Kaufman, J., Rennie, A. & Clement, M., 03/2015. 6 p.

    Research output: Contribution to conference - Without ISBN/ISSN › Conference paper › peer-review

  3. Published

    Determination of head losses in drip irrigation laterals with cylindrical in-line type emitters through CFD analysis

    Celik, K., Karayel, D., Lupeanu, M., Rennie, A. E. W. & Akinci, I., 20/02/2015, In: Bulgarian Journal of Agricultural Science. 21, 3, p. 703-710 8 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  4. Published

    Designing advanced filtration media through metal additive manufacturing

    Burns, N., Burns, M., Travis, D., Geekie, L. & Rennie, A., 02/2015. 9 p.

    Research output: Contribution to conference - Without ISBN/ISSN › Conference paper › peer-review

  5. Published

    Adaptive Materials: Utilising additive manufactured scaffolds to control self-organising material aggregation

    Blaney, A., Alexander, J., Dunn, N., Richards, D., Rennie, A. & Anwar, J., 2015.

    Research output: Contribution to conference - Without ISBN/ISSN › Conference paper › peer-review

  6. Published

    Horizon 2020 TWEETHER project for W-band high data rate wireless communications

    Paoloni, C., Letizia, R., Napoli, F., Ni, Q., Rennie, A., Zimmerman, R., Andre, F., Pham, K., Krozer, V., Magne, F., Burciu, I., Ramirez, A., Rocchi, M., Marilier, M. & Vilar, R., 2015, Vacuum Electronics Conference (IVEC), 2015 IEEE International . IEEE, 2 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  7. Published

    Non-stochastic lattice structures for novel filter applications fabricated via additive manufacturing

    Hasib, H., Rennie, A., Burns, N. & Geekie, L., 2015, In: Filtration. 15, 3, p. 174-180 7 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  8. Published

    Single camera photogrammetry for reverse engineering and fabrication of ancient and modern artifacts

    Kaufman, J., Rennie, A. E. W. & Clement, M., 2015, In: Procedia CIRP. 36, p. 223-229 7 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  9. 2014
  10. Unpublished

    Additive manufacturing in assistive product design development

    Sembiring, E., Rennie, A. & Laha, S., 12/2014, (Unpublished).

    Research output: Contribution to conference - Without ISBN/ISSN › Poster

  11. Unpublished

    Non-stochastic lattice structures for novel filter applications fabricated via additive manufacturing

    Hasib, H., Rennie, A., Burns, N. & Geekie, L., 12/2014, (Unpublished).

    Research output: Contribution to conference - Without ISBN/ISSN › Poster

  12. Published

    Touching history: 3D replica artifacts

    Kaufman, J. & Rennie, A., 12/2014, Ancient Egypt, 15, 3, p. 32-33 2 p.

    Research output: Contribution to specialist publication › Article

  13. Published

    Non-stochastic lattice structures for novel filter applications fabricated via additive manufacturing

    Hasib, H., Rennie, A., Burns, N. & Geekie, L., 11/2014, The Filtration Society 50th Anniversary International Conference and Exhibition: Proceedings of the . The Filtration Society, 10 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  14. Published

    Filtration efficiency gains by fabrication using additive manufacturing

    Burns, N., Vijayakumar, B., Rennie, A. & Geekie, L., 10/2014, Proceedings of the European Conference on Fluid-Particle Separation. 2 p. M3P2

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  15. Published

    Introducing functionality to filter media

    Vijayakumar, B., Rennie, A., Burns, N., Travis, D. & Battersby, P., 10/2014, In: Filtration. 14, 4, p. 217-222 6 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  16. Published

    Maximising open area whilst retaining strength in novel metal additive manufactured filter media

    Burns, N., Burns, M., Travis, D., Geekie, L., Hasib, H. & Rennie, A., 10/2014. 1 p.

    Research output: Contribution to conference - Without ISBN/ISSN › Abstract › peer-review

  17. Published

    The use of additive manufacture for metallic bipolar plates in polymer electrolyte fuel cell stacks

    Dawson, R., Patel, A., Rennie, A. & White, S., 28/09/2014, In: Chemical Engineering Transactions. 41, p. 175-180 6 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  18. Published

    Automated software for streamlining optimisation of resource planning for an additive manufacturing system

    Lupeanu, M., Rosu, M.-M., Doicin, C., Rennie, A. & Neagu, C., 09/2014, Proceedings of 3rd International Conference Advances in Engineering & Management (ADEM 2014). 8 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  19. Published

    Effects of scan direction and orientation on mechanical properties of laser sintered polyamide-12

    Nelson, J. A., Galloway, G., Rennie, A., Abram, T. & Bennett, G. R., 09/2014, In: International Journal of Advanced Design and Manufacturing Technology. 7, 3, p. 19-25 7 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  20. Published

    Innovations in filtration through additive manufacturing: Paper: EP140165

    Burns, N., Burns, M., Travis, D., Geekie, L. & Rennie, A., 09/2014. 6 p.

    Research output: Contribution to conference - Without ISBN/ISSN › Conference paper › peer-review

  21. Published

    Improved filtration using additive manufacturing

    Burns, N., Geekie, L., Travis, D., Burns, M., Weston, D. P. & Rennie, A., 07/2014.

    Research output: Contribution to conference - Without ISBN/ISSN › Conference paper › peer-review

  22. Published

    Design, innovation and a new age for filtration

    Burns, N., Geekie, L., Travis, D., Burns, M. & Rennie, A., 06/2014.

    Research output: Contribution to conference - Without ISBN/ISSN › Abstract

  23. Published

    Reverse engineering using close range photogrammetry for additive manufactured reproduction of Egyptian artefacts and other objets d'art

    Kaufman, J., Rennie, A. & Clement, M., 06/2014, Proceedings of the ASME 2014 12th Biennial Conference on Engineering System Design and Analysis (ESDA 2014): Volume 1: Applied Mechanics; Automotive Systems; Biomedical Biotechnology Engineering; Computational Mechanics; Design; Digital Manufacturing; Education; Marine and Aerospace Applications. American Society of Mechanical Engineers (ASME), 8 p. ESDA2014-20304

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  24. Published

    Research strategy on developing additive manufactured bespoke ophthalmic instruments assisted by an online integrated platform

    Lupeanu, M., Rennie, A., Rosu, M.-M. & Moagar-Poladian, G., 04/2014, In: Buletinul Ştiinţific al Universităţii Politehnica Bucureşti, Seria D – Inginerie Mecanică. 76, 2, p. 143-162 20 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  25. Unpublished

    Redesign of custom-fitted surgical guide with targeted functional analysis fabricated via SLM

    Lupeanu, M., Rennie, A. & Neagu, C., 31/03/2014, (Unpublished).

    Research output: Contribution to conference - Without ISBN/ISSN › Poster

  26. Published

    The business model for the functional rapid manufacturing supply chain

    Hasan, S., Rennie, A. & Hasan, J., 01/2014, In: Studia Commercialia Bratislavensia. 6, 24, p. 536-552 17 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  27. 2013
  28. Unpublished

    How to keep it in for longer: innovation in the Critical Care Unit

    Laha, S. & Rennie, A., 6/11/2013, (Unpublished).

    Research output: Contribution to conference - Without ISBN/ISSN › Other

Previous 1 2 3 4 5 6 7 8 ...10 Next

Back to top