Rights statement: This is the author’s version of a work that was accepted for publication in Journal of Alloys and Compounds. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Alloys and Compounds, 938, 2023 DOI: 10.1016/j.jallcom.2022.168617
Accepted author manuscript, 1.59 MB, PDF document
Available under license: CC BY-NC-ND: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License
Final published version
Research output: Contribution to Journal/Magazine › Journal article › peer-review
Research output: Contribution to Journal/Magazine › Journal article › peer-review
}
TY - JOUR
T1 - Force enhanced wire laser additive manufacturing of aluminum and titanium alloys
AU - Zhao, Zhe
AU - Xu, Shuoheng
AU - Liu, Jian
AU - Zhang, Xiaohan
AU - Xia, Min
AU - Hu, Yaowu
N1 - This is the author’s version of a work that was accepted for publication in Journal of Alloys and Compounds. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Alloys and Compounds, 938, 2023 DOI: 10.1016/j.jallcom.2022.168617
PY - 2023/3/25
Y1 - 2023/3/25
N2 - Brittle intermetallic compound formation is typically difficult to avoid during fusion joining of dissimilar metals. In this paper, a new approach called force enhanced wire laser additive manufacturing is proposed to join aluminum and titanium alloys. Ti6Al4V titanium alloy single track was additively fabricated on AA7075 plate successfully, through two liquid pools of the wire and the substrate, separated by a buckled unmelted part of the wire, leading to a mechanically interlocked interface. The effects of manufacturing parameters including laser power, wire feeding speed, scanning speed and initial contact force between wire and substrate on the surface morphology, internal interface microstructure and formation of intermetallic compounds were investigated through high-speed camera, spectrometer, laser topography, optical imaging, SEM imaging, XRD characterizations along with numerical simulations at different scales. And the maximum tensile strength reached 380MPa in the tensile test. The experimental and numerical results indicate that the thermal modulation approach can effectively control the formation of brittle compounds between titanium and aluminum alloys and that the initial contact force ensures a good bond between the two metals.
AB - Brittle intermetallic compound formation is typically difficult to avoid during fusion joining of dissimilar metals. In this paper, a new approach called force enhanced wire laser additive manufacturing is proposed to join aluminum and titanium alloys. Ti6Al4V titanium alloy single track was additively fabricated on AA7075 plate successfully, through two liquid pools of the wire and the substrate, separated by a buckled unmelted part of the wire, leading to a mechanically interlocked interface. The effects of manufacturing parameters including laser power, wire feeding speed, scanning speed and initial contact force between wire and substrate on the surface morphology, internal interface microstructure and formation of intermetallic compounds were investigated through high-speed camera, spectrometer, laser topography, optical imaging, SEM imaging, XRD characterizations along with numerical simulations at different scales. And the maximum tensile strength reached 380MPa in the tensile test. The experimental and numerical results indicate that the thermal modulation approach can effectively control the formation of brittle compounds between titanium and aluminum alloys and that the initial contact force ensures a good bond between the two metals.
KW - Force enhanced
KW - Laser additive manufacturing
KW - Titanium
KW - Aluminum
U2 - 10.1016/j.jallcom.2022.168617
DO - 10.1016/j.jallcom.2022.168617
M3 - Journal article
VL - 938
JO - Journal of Alloys and Compounds
JF - Journal of Alloys and Compounds
SN - 0925-8388
M1 - 168617
ER -