Rights statement: This is the author’s version of a work that was accepted for publication in Journal of Cleaner Production. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Cleaner Production, 268, 2020 DOI: 10.1016/j.jclepro.2020.122077
Accepted author manuscript, 753 KB, PDF document
Available under license: CC BY-NC-ND: Creative Commons Attribution-NonCommercial-NoDerivatives 4.0 International License
Final published version
Research output: Contribution to Journal/Magazine › Journal article › peer-review
Research output: Contribution to Journal/Magazine › Journal article › peer-review
}
TY - JOUR
T1 - Understanding powder degradation in metal additive manufacturing to allow the upcycling of recycled powders
AU - Powell, Dan
AU - Rennie, Allan
AU - Geekie, Louise
AU - Burns, Neil
N1 - This is the author’s version of a work that was accepted for publication in Journal of Cleaner Production. Changes resulting from the publishing process, such as peer review, editing, corrections, structural formatting, and other quality control mechanisms may not be reflected in this document. Changes may have been made to this work since it was submitted for publication. A definitive version was subsequently published in Journal of Cleaner Production, 268, 2020 DOI: 10.1016/j.jclepro.2020.122077
PY - 2020/9/20
Y1 - 2020/9/20
N2 - To ensure the financial viability of powder-based additive manufacturing technologies, the recycling of powders is common practice. This paper shows the lifecycle of metal powder in additive manufacturing, investigating powder manufacture, powder usage, mechanisms of powder degradation and the usage of end-of-life powder. Degradation of powders resulting from repeated reuses was found to be a widespread problem; components produced from heavily reused powders are typically of a lower quality, eventually rendering the powder unusable in additive manufacturing. Powder degradation was found to be dependent on many variables, preventing the identification of a definitive end-of-life point for powders. The most accurate method of determining powder quality was found to be the production and analysis of components using these powders. Uses for degraded powder had not been previously identified in literature, warranting the investigation of potential solutions to prevent powder waste. Amongst other waste-reducing solutions, plasma spheroidisation was identified as a promising method to avoid powder disposal for approximately 12.5% of produced powders, creating particles similar to virgin powder from end-of-life powder. Returning end-of-life powders to the supplier for upcycling may be the only financially viable solution to reduce waste within the industry. The compilation of research within this paper aims to enable users of additive manufacturing to conduct further research and development into powder upcycling.
AB - To ensure the financial viability of powder-based additive manufacturing technologies, the recycling of powders is common practice. This paper shows the lifecycle of metal powder in additive manufacturing, investigating powder manufacture, powder usage, mechanisms of powder degradation and the usage of end-of-life powder. Degradation of powders resulting from repeated reuses was found to be a widespread problem; components produced from heavily reused powders are typically of a lower quality, eventually rendering the powder unusable in additive manufacturing. Powder degradation was found to be dependent on many variables, preventing the identification of a definitive end-of-life point for powders. The most accurate method of determining powder quality was found to be the production and analysis of components using these powders. Uses for degraded powder had not been previously identified in literature, warranting the investigation of potential solutions to prevent powder waste. Amongst other waste-reducing solutions, plasma spheroidisation was identified as a promising method to avoid powder disposal for approximately 12.5% of produced powders, creating particles similar to virgin powder from end-of-life powder. Returning end-of-life powders to the supplier for upcycling may be the only financially viable solution to reduce waste within the industry. The compilation of research within this paper aims to enable users of additive manufacturing to conduct further research and development into powder upcycling.
KW - Additive Manufacturing
KW - Metallurgy
KW - Powder Degradation
KW - Upcycling
KW - Plasma Spheroidisation
U2 - 10.1016/j.jclepro.2020.122077
DO - 10.1016/j.jclepro.2020.122077
M3 - Journal article
VL - 268
JO - Journal of Cleaner Production
JF - Journal of Cleaner Production
SN - 0959-6526
M1 - 122077
ER -