Home > Research > Browse

Results for Additive manufacturing

Publications & Outputs

  1. Effect of melting modes on microstructure and tribological properties of selective laser melted AlSi10Mg alloy

    Wu, H., Ren, Y., Ren, J., Cai, A., Song, M., Liu, Y., Wu, X., Li, Q., Huang, W., Wang, X. & Baker, I., 8/12/2020, In: Virtual and Physical Prototyping. 15, sup1, p. 570-582 13 p.

    Research output: Contribution to journalJournal articlepeer-review

  2. Grain refinement in laser powder bed fusion: The influence of dynamic recrystallization and recovery

    Sabzi, H. E., Aboulkhair, N. T., Liang, X., Li, X. H., Simonelli, M., Fu, H. & Rivera-Díaz-del-Castillo, P. E. J., 30/11/2020, In: Materials and Design. 196, 10 p., 109181.

    Research output: Contribution to journalJournal articlepeer-review

  3. Controlling crack formation and porosity in laser powder bed fusion: Alloy design and process optimisation

    Sabzi, H. E., Maeng, S., Liang, X., Simonelli, M., Aboulkhair, N. T. & Rivera-Díaz-del-Castillo, P. E. J., 1/08/2020, In: Additive Manufacturing. 34, 14 p., 101360.

    Research output: Contribution to journalJournal articlepeer-review

  4. Generation of graded porous structures by control of process parameters in the selective laser melting of a fixed ratio salt-metal feedstock

    Aboulkhair, N. T., Zhao, G., Hague, R. J. M., Kennedy, A. R., Ashcroft, I. A. & Clare, A. T., 1/07/2020, In: Journal of Manufacturing Processes. 55, p. 249-253 5 p.

    Research output: Contribution to journalJournal articlepeer-review

  5. The impact of post manufacturing treatment of functionally graded Ti6Al4V scaffolds on their surface morphology and mechanical strength

    Khrapov, D., Koptyug, A., Manabaev, K., Leonard, F., Mishurova, T., Bruno, G., Cheneler, D., Loza, K., Epple, M., Surmenev, R. & Surmeneva, M., 1/03/2020, In: Journal of Materials Research and Technology. 9, 2, p. 1866-1881 16 p.

    Research output: Contribution to journalJournal articlepeer-review

  6. Experimental Platform to Facilitate Novel Back Brace Development for the Improvement of Spine Stability

    Cooper, L., Gullane, A., Harvey, J., Hills, A., Zemura, M., Martindale, J., Rennie, A. & Cheneler, D., 16/09/2019, In: Computer Methods in Biomechanics and Biomedical Engineering. 22, 15, p. 1163-1173 11 p.

    Research output: Contribution to journalJournal articlepeer-review

  7. Effect of processing parameters on the densification, microstructure and crystallographic texture during the laser powder bed fusion of pure tungsten

    Sidambe, A. T., Tian, Y., Prangnell, P. B. & Fox, P., 1/01/2019, In: International Journal of Refractory Metals and Hard Materials. 78, p. 254-263 10 p.

    Research output: Contribution to journalJournal articlepeer-review

  8. A microstructure sensitive model for deformation of Ti-6Al-4V describing Cast-and-Wrought and Additive Manufacturing morphologies

    Galindo-Fernández, M. A., Mumtaz, K., Rivera-Díaz-del-Castillo, P. E. J., Galindo-Nava, E. I. & Ghadbeigi, H., 15/12/2018, In: Materials and Design. 160, p. 350-362 13 p.

    Research output: Contribution to journalJournal articlepeer-review

  9. Salt-metal feedstocks for the creation of stochastic cellular structures with controlled relative density by powder bed fabrication

    Zhao, G., Ashcroft, I. A., Hague, R. J. M., Kennedy, A. R. & Clare, A. T., 5/07/2018, In: Materials and Design. 149, p. 63-72 10 p.

    Research output: Contribution to journalJournal articlepeer-review

  10. Material interactions in laser polishing powder bed additive manufactured Ti6Al4V components

    Tian, Y., Gora, W. S., Cabo, A. P., Parimi, L. L., Hand, D. P., Tammas-Williams, S. & Prangnell, P. B., 03/2018, In: Additive Manufacturing. 20, p. 11-22 12 p.

    Research output: Contribution to journalJournal articlepeer-review

  11. Enhancing surface finish of additively manufactured titanium and cobalt chrome elements using laser based finishing

    Gora, W. S., Tian, Y., Cabo, A. P., Ardron, M., Maier, R. R. J., Prangnell, P., Weston, N. J. & Hand, D. P., 2016, In: Physics Procedia. 83, p. 258-263 6 p.

    Research output: Contribution to journalJournal articlepeer-review

More results »