Home > Research > Structures, Materials and Manufacturing > Publications & Outputs

Research

View graph of relations

Structures, Materials and Manufacturing

31 - 40 out of 968Page size: 10
RSS feed of this list
Sort by: Type
  1. Chapter
  2. Published

    Laser direct metal deposition: theory and applications in manufacturing and maintenance

    Pinkerton, A. J., 2010, Advances in laser materials processing : technology, research and applications. Lawrence, J. (ed.). Oxford: Woodhead Publishing Limited

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  3. Published

    Three-dimensional Modeling of Stress Transfer, Stiffness Degradation, failure and Transverse Cracking in Composite Laminates.

    Ye, J., 2009, Advances in Engineering Mechanics. Qin, Q. & Sun, B. (eds.). Nova Science Publishers, Vol. 1. p. 127-165 39 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  4. Published

    Imaging internal structure with electromagnetic induction tomography.

    Ma, X., Peyton, A. J., Soleimani, M. & Lionheart, W. R. B., 12/03/2007, Instrumentation and Measurement Technology Conference, 2006. IMTC 2006. Proceedings of the IEEE. IEEE, p. 299 -303

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  5. Published

    Failure of pultruded GRP WF-section webs in compression - an experimental investigation.

    Turvey, G., 2006, Proceedings of the 12th European conference on composite materials (ECCM-12).

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  6. Published

    An FE analysis of the stresses in pultruded GRP single-bolt tension joints and their implications for joint design.

    Turvey, G. & Wang, P., 2006, Proceedings of the 6th international conference on computational mechanics (ECCM 2006).

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  7. Published

    Single-bolt tension joints in pultruded GRP plate - effects of elevated temperature on failure loads, failure modes, load orientation and joint efficiency.

    Turvey, G. & Wang, P., 2006, Proceedings of the 2nd international conference on joining plastics 2006..

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  8. Published

    Eddy current measurement of the electrical conductivity and porosity of metal foams.

    Ma, X. & Peyton, A. J., 8/11/2004, Proceedings of the IEEE Instrumentation and Measurement Technology Conference, 2004. IMTC 04.. IEEE, Vol. 1. p. 127-132 6 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  9. Published

    Novel computer-based processing system for partial discharge detection and diagnosis.

    Ma, X., Zhou, C. & Kemp, I. J., 8/11/2004, Proceedings of the IEEE Instrumentation and Measurement Technology Conference, 2004. IMTC 04.. IEEE, Vol. 1. p. 684-688 5 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  10. Published

    Molten metal flow visualisation using mutual induction tomography (MIT).

    Soleimani, M., Lionheart, W. R. B., Peyton, A. J. & Ma, X., 2004, 2004 Proceedings of the ASME 7th Biennial Conference on Engineering Systems Design & Analysis. Vol. 1. 6 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

  11. Published

    Vibration frequencies and mode shapes of pultruded GRP circular plates with central circular cut-outs.

    Turvey, G. J. & Mulcahy, N., 2004, Proceedings of the 4th international conference on thin-walled structures: thin-walled structures: advances in research, design and manufacturing technology. p. 927-934 8 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Chapter

Previous 1 2 3 4 5 6 7 8 ...97 Next

Back to top