Home > Research > Publications & Outputs >

Research

« Back

Find by keywords:

Engineering

121 - 130 out of 704Page size: 10
  1. Published

    LIGA-based Slow Wave Structure for a THz Vacuum Amplifier

    Bouamrane, F., Bouvet, T., Megtert, S., Brunetti, F., Mineo, M., Paoloni, C., Tamburri, E., Terranova, M. L., Ulisse, G., Di Carlo, A., Marchesin, R., Pham, K., Durand, A. J., Kotiranta, M., Krozer, V., Guiset, P., De Rossi, A., Schnell, J. P., Legagneux, P. & Dolfi, D. & 6 others, Fiorello, A. M., Dispenza, M., Secchi, A., Zhurbenko, V., Gohier, A. & Cojocaru, C.-S., 06/2011, Proceedings of High Aspect Ratio Micro Structure Conference HARMST 2011. Taiwan, 1 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  2. Published

    Optimisation of build orientation for FDM additive manufactured products

    Hambali, R. H., Vaudelin, M. & Rennie, A., 06/2011.

    Research output: Contribution to conference - Without ISBN/ISSN › Poster › peer-review

  3. Published

    Polarities of function and form using additive manufacturing - where the middle ground might be in achieving a creative balance for SMEs

    Kaufman, J., Rennie, A. & Quayle, S., 06/2011, Rapid Design, Prototyping and Manufacturing: Proceedings of the Twelfth Conference on. CRDM Ltd, p. 135-143 9 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  4. Published

    Move from Online Test to Fault-tolerant: Design and Simulation of a Multi-Functional MEMS Sensor

    Xu, Z., Richardson, A., Begbie, M. & Wang, C., 16/05/2011, Proceedings of the IEEE International Mixed Signals, Sensors and Systems Test Workshop. USA: IEEE COMPUTER SOC, p. 88-95 8 p.

    Research output: Contribution in Book/Report/Proceedings - With ISBN/ISSN › Conference contribution/Paper › peer-review

  5. Published

    Microcomputed tomography analysis of intralayer porosity generation in laser direct metal deposition and its causes

    Ahsan, M. N., Bradley, R. & Pinkerton, A. J., 05/2011, In: Journal of Laser Applications. 23, 2, p. - 10 p., 022009.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  6. Published

    The influence of profiled sheeting thickness and shear connector's position on strength and ductility of headed shear connector

    Qureshi, J., Lam, D. & Ye, J., 05/2011, In: Engineering Structures. 33, 5, p. 1643-1656 14 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  7. Published

    High-Mobility Low-Voltage ZnO and Li-Doped ZnO Transistors Based on ZrO2 High-k Dielectric Grown by Spray Pyrolysis in Ambient Air

    Adamopoulos, G., Thomas, S., Woebkenberg, P. H., Bradley, D. D. C., McLachlan, M. A. & Anthopoulos, T. D., 26/04/2011, In: Advanced Materials. 23, 16, p. 1894-1898 5 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  8. Published

    Combined digital imaging of mixed-field radioactivity with a single detector.

    Gamage, K., Joyce, M. J. & Adams, J., 11/04/2011, In: Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment. 635, 1, p. 74-77 4 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  9. Published

    Porous structures fabrication by continuous and pulsed laser metal deposition for biomedical applications; modelling and experimental investigation

    Ahsan, M. N., Paul, C. P., Kukreja, L. M. & Pinkerton, A. J., 1/04/2011, In: Journal of Materials Processing Technology. 211, 4, p. 602-609 8 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

  10. Published

    An investigation into the environmental impact of product recovery methods to support sustainable manufacturing within small and medium-sized enterprises (SMEs)

    Appleby, M., Lambert, C., Rennie, A. & Buckley, A., 04/2011, In: International Journal of Manufacturing, Materials, and Mechanical Engineering (IJMMME). 1, 2, p. 1-18 18 p.

    Research output: Contribution to Journal/Magazine › Journal article › peer-review

Previous 1...9 10 11 12 13 14 15 16 ...71 Next

Back to top